More Filters
Need driver side rear axle from 4 door, manual 6 speed turbo Mazdaspeed6.
Can you tell me what the rear end is? 8.8? Gears aswell I'm looking for posi 8.8 rear end with 373 gears or 410s
I need L and R rear disc brake "backing plates" (rear cover opened - axle clips removed) and Emerg. cables with nut/bolt hardware only (no rotors or calipers) packed into USPS Large flat rate box, unless Parcel Select ground is cheaper - Thanks!
I am looking for a rear semi float long side (driver's side, LH) axle shaft for my 84 FJ60. Needs to have good bearing and seal surfaces as I just found out when changing bearings that I already have one that does not. Thanks.
I am looking for a rear semi float long side (driver's side, LH) axle shaft for my 84 FJ60. Needs to have good bearing and seal surfaces as I just found out when changing bearings that I already have one that does not. Thanks.
8.8 rear axle from a Ford Explorer between 1995-2001
Hi gyuys, I ripped the inside CV boot on my left rear axle. I want to check if anyone have a deal on an axle or pair of axles before I change the cv boot only. Im located on the Eastcoast in Canada but It could be shipped to a forwarder In the USA also. its for a 64 inches wide X3 XDS. Thanks
Chrysler 8.25 fully loaded rear with 4.10 ratio set up for leafs Dana 35 with 4.10 ratio rear axle also set up for leafs , either one will work
Need it Complete ! Let me know what you have, I am in Long Island NY and will travel within reasonable distance D.
Looking for a passenger rear axle for a 6 speed manual transmission must be oem axle... hollow shafts on oem and solid shafts on aftermarket... aftermarket axles vibrate at high speeds. Also looking for the ac line that runs from the compressor to the ac receiver dryer, it s a high pressure line located under the car along the subframe
I d like to find a rear diff guard for the Wolf/P38/Td5/Puma axle. (Bottom bolts on side of housing, not bottom). I ll take ANYTHING remotely functional. thanks!!!
over a month agoOberlin, KSFor SaleWantedReport Listing
The first picture is a perfect example of what I am looking for, .... I am needing a complete rear end, ... swingarm, rear axle, rims, etc... out of any ATV, whether an old 3 wheeler or a 4 wheeler, old or new. Preferably an aluminum swingarm, but I could work with a steel one as well if it's not all rusted up. As long as it is a chain drive it will probably work for me. If you have, or know so...
Looking for usable or rebuildable rear axle spring mounting pivots. At least one needed. The spring center bolt hole is hogged out on one of mine. It must have been run for a long time with loose u-bolts.
over a month agoAuto Parts for SaleWantedReport Listing
Title basically states it. I need an axle from a 2007+ Toyota Tundra with 5.7L engine; aka the 10.5" differential. I need the housing to be straight. I don't need the brakes. While I really don't need the axle shafts, I would take them... axle shafts only needed to figure out where the ends land in the diff area. Gearing isn't mission critical so it can be 4.10 or 4.30. I am in Georgetown, Cali...
over a month agoAuto Parts for SaleWantedReport Listing
Looking for a chevy or gmc rear dana 60. Bonus if its 4.09, and has brakes that work enough for on/off a trailer. Will pay cash in person. Located in lincoln, ca 95648
over a month agoAuto Parts for SaleWantedReport Listing
Searching for what is in the title. I can change gear ratios, with the E locker or without. Ideally with the ABS lines intact. Thank you!
Similar
Looking for driver side rear axle shaft for an all wheel drive Mazda Speed 6.
Looking for 2 shock toggle bolts for the rear knee action shocks. The ones that attach to the axle side. I think they are the same for all 41-46 front or rear.
I'm located in Philly area and am looking to pick up at least a front locking axle for my 97 but I'd take a rear as well if you have it. My front axle spring perch has rot holes and I figure it would probably be easier to just replace the whole...
I'm located in Philly area and am looking to pick up at least a front locking axle for my 97 but I'd take a rear as well if you have it. My front axle spring perch has rot holes and I figure it would probably be easier to just replace the whole...
Looking for the backing plates primarily, but shoes, springs, T bolts that mount to the axle flange would be a plus. Thanks, John.
ALWAYS LOOKING FOR NICE OLD CENTERLINE VW WIDE-5 WHEELS & OTHET NEAT AFTERMARKET VW WHEELS! Will Buy Outright And/Or Have Tons Of Good VW Trading Material. Need A 13 by 6 wide-5 With ORIGINAL SATIN FINISH WITH FACTORY MACHINE MARKS PRESENT! These Are The Ticket For Running A Wide Tire On A Short Axle Beetle With No Mods & Will Also Fit On A Straight Axle Split Bus Under The Rear Skirt No Proble...
Sponsored Links (Register now to hide all advertisements) freestar.config.enabled_slots.push({ placementName: "fordbarn_leaderboard_forums_inlinst_2", slotId: "fordbarn_leaderboard_forums_inlinst_2" }); I m starting with 4 wheels, 3 hub caps, two mirrors, a grill, an axle, and some misc. sheet metal. It won t be a concourse restoration for sure -I m hoping to make the antique nationals in 2022!...
Looking for a pair of rear a-arm suspension links. Just need the left and right link. I'm assuming they're the same for both Rover type and Sals rear axles. Mine is a sals. Thanks.
I have a set of 5.14 gears but Im looking for a set of 4.10 Let me know what you can do! Ill buy a complete axle if I need too but just need the gears.
Your Listing Here
1 + ... Next >