12-Bolt Rear End Housing Only for Chevelle w3 Seamless DOM tubes professionally installed, axle ends cut for C-Clip Eliminators, comes w411 Ring Pinion installed wyoke NO brakes or backing plates, $1000.00For an additional $150.00 will include 33 Spline Moser Spool wCarrier Bearings. NO AXLES.E-mail phone number for response
Guys cleaning out the shop some more again. I have a couple pairs of used axles for these cars. Please call to discuss. NO TEXTING SETUP Must call or leave a message. I will hallar back at ya. NO late calls after 9pm during the week. $100.00 a pair.phone
For sale is a 12 bolt Chevy rear end with 3.40 ratio gears removed from a 1973 Chevy C10 pickup truck. It is a 5 lug rear axle and the inspection cover was removed to inspect the gears and they looked good, no excessive wear or obvious damage. The right side brake drum is missing but all the brake hardware seems to be there. This rear end should fit 1973-1981 Chevy, Blazer and GMC ton pickups. ...
selling three different Richmond ring and pinion setsall in boxes..used but in great cond The 8.875 513 Gear has about 20 passes on it.The 8.500 513 Gear is for a gm 10 bolt all were in a 69 chevelle 100.00 each set ....
Pulled from a runningdriving 69 Chevy C10. Upgrading the drivetrain so this one is no longer needed. It is the original rear end and may need work before being put back into use.
$525

GM 12 bolt

GM 12 bolt for a truck 6 lug. 50 14 wide, new Summer Brothers axles, new Richmond ring gear 3.73, positive traction unit, and complete new drum brake set up with parking break cables
1978 front Dana 44 housing with open 373 gear, no axles or spindles - 1978 GM 12 bolt rear end with new locker and 373 gears. Both custom fit to 1993 Silverado. $500.00 for both Pete
This rear end is in very good condition. It has C-clip eliminators, 4.88 posi with GM gears, long wheel studs. The rear end measures 55 14 from inside axle housing tube flange to inside axle housing tube flange or 61 from outside axle flange to outside of axle flange. Seals and bearing are very good. It is clean and ready to install. This rear end fits other GM cars, its up to you to find out w...
12 bolt Rear for GMStrange Spool C-33 D1530 4 series 33 Spline $200538 Richmond pro gears 4 series $150Strange axles 33 spline with C clip eliminators 21 long for 12 bolt-narrowed $100Will sell separately.No housing just the spoolcarrier posi unit, gears and axles. Fits all these cars and moreGM, Chevy, Pontiac, Oldsmobile, z-28, z28, z28, ss, 327, 350, 383, 396, 400, 402, 409, 426, 427, 440, 4...
GM 12 bolt rear end. I just removed it from my 67 Chevelle. It is an Oldsmobile 12 bolts on cover, 10 bolts on ring gear. It has an open carrier with 3.08 gears. I think it will fit a 64-72 Chevelle and lemans, tempest, skylark, gto, 442. It was in working order when I removed it to replace it with a Chevy 12 bolt. It will fit in a 64-72 Chevelle or Buick Olds Pontiac models.Chevelle, nova, bbc...
I have a newnever installed Moser 12 bolt GM 68-72 CHEVELLE, CUTLASS, PONTIAC, BUICK.I bought it this last summer in its original shipping crate.it has an Eaton posi unit with yukon 355 gears with 33 spline c clip Eliminator axles with disc brakes a large 1350 yoke. Ive installed the axles but not disc brakes yet.axles are standard gm small bolt pattern with stock size studs ,disc brakes fit in...
For sale is a 12 bolt Chevy rear end with 3.40 ratio gears removed from a 1973 Chevy C10 pickup truck. It is a 5 lug rear axle and the inspection cover was removed to inspect the gears and they looked good, no excessive wear or obvious damage. The right side brake drum is missing but all the brake hardware seems to be there. This rear end should fit 1973-1981 Chevy, Blazer and GMC ton pickups. ...