last weekPhoenix, AZ+35 milesTools for Sale
Tool Box & Tools & Equipment have been used very little. They are like NEW. Everything has been in storage for a few years. Some tools & equipment are still in the original boxes. Not all tools & equipment are listed. ALL TOOL BOX & TOOLS & EQUIPMENT SOLD IN LOT PRICE. NO SINGLE SALES ITEMS. Phoenix, Az. 214-215-1221
yesterdayPhoenix, AZ+35 milesTools for Sale
Used Sears Craftsman wet dry vac 16 gallon 3.25 peak hp. A little dirty from sitting in the shed. Works great! $50 o.b.o.
yesterdayPhoenix, AZ+35 milesTools for Sale
This is a Curtiss-Wright Electric prop pitch unit that was used on the C-124 Globemaster cargo plane of WWII and the Koren War era.Its function was to change the pitch of the huge propeller blades while the aircraft was in flight.These units have been overhauled by the US Government and they are like brand new.They run well on 6 to 36 volts and they produce tremendous torque.The motor is equipp...
yesterdayPhoenix, AZ+35 milesTools for Sale
I have 14 foot length and a 41 foot length of genuine CM lever hoist chain. This chain is certified for lifting and retails for approximately $8.00 per foot.It is a real bargain for only $3.00 per foot. The hoist is NOT for sale.That is a dollar bill in the photo to give you an idea of the chain size.I do not respond to Craigslist e-mails, but you are welcome to call me at
yesterdayPhoenix, AZ+35 milesTools for Sale
This is a 110 volt linear actuator that was removed in perfect condition from a very expensive treadmill. The overall extended length is 12 34 and the overall retracted length is 9 12. The horsepower is 112. The gear ratio is 1291, and the RPM is 80. I do not respond to texts or e-mails, but you are welcome to call me at .
yesterdayPhoenix, AZ+35 milesTools for Sale
I have several 12 volt and 120 volt muffin fans for sale. They range in price from $5 to $10.I do not reply to e-mail inquiries. Call me at
yesterdayPhoenix, AZ+35 milesTools for Sale
This tool is still in the original packaging complete with instructions.I do not respond to Craigslist texts or e-mails, but you are welcome to call me at .
yesterdayPhoenix, AZ+35 milesTools for Sale
I have 2 of these tool holders. They weigh 4 pounds each and they take 14 thick x 34 square inserts. I have 7 new inserts to go with the holders. The price is $20 for I holder or $30 for both.I do not respond to Craigslist texts or e-mails, but you are welcome to call me at .
yesterdayPhoenix, AZ+35 milesTools for Sale
This is a high quality aircraft motor that probably was used to actuate landing gear, flaps, or other equipment on large WWII type aircraft. It is very powerful for its size. It is 4 in diameter, 7 38 long overall including shaft and power lugs. It is 6 long from the front of the mounting flange to the back of the motor. The shaft is 916 diameter X 10 splines X 12 long. A 12 pulley or sprocket ...
yesterdayPhoenix, AZ+35 milesTools for Sale
Vintage Die Handle and Dies. Dies 14-20, 516-18, 2 38-16. 716-14, 12-13, and one oddball die 716-12 that doesnt fit the Die Handle.
yesterdayPhoenix, AZ+35 milesTools for Sale
This motor is new old stock. It would be perfect to run a small mill or lathe with full control from 0 to 2500 RPM just by turning a small knob.I have my drill press set up like this and it is sweet I do not respond to e-mail or texts, but you are welcome to call me at .
yesterdayPhoenix, AZ+35 milesTools for Sale
This 34 horse power Reliance Brand Motor will provide the owner with variable speed to run saws, lathes, drill presses, sanders, and You would have to couple a speed controller to the motor for a complete system. I also have some controllers available.I have built several variable systems for some of my tools. Come by and take a look if you like.I do not respond to Craigslist e-mails or texts, ...
yesterdayPhoenix, AZ+35 milesTools for Sale
I Have a Like New Arctic Cove EVC 500 for Sale.This Unit is Like New. Only Used a Few Times.It Sells for Up To 400.00 New.Buy it Today for Only 140.00.
yesterdayPhoenix, AZ+35 milesTools for Sale
This is a brand new motor that is ready to go to work in your shop.It has a drive shaft on each end of the motor and it has a power cord with a 3 prong plug. It also has a built in ONOFF switch.I do not answer e-mails or texts but you are welcome to call me at .