I am looking for an 78 mm or 78.4 mm crankshaft. must be in great condition and ready to put into a motor. I am looking for a VW crank that has been welded or a forged crank, nothing cast. Thanks, Larry
I am looking for a Hurst line loc switch, the kind that has a red lever on it not just a button type, I ran one on my car back in the early eighties and I am looking to add one to my current 56 project, let me know what you have. Thank you, I appreciate any responses. Larry
11-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
2001 thru 2005 Chrysler PT Cruiser complete front clip . It includes hood, fenders , grill , front bumper with fog lights , headlights , antenna , hood emblem, Hinges if needed . Hood rubber , cowling rubber , prop rod . Damage A small scratch on right fender in picture below antenna , and small crease on the hood where the hood prop rod sets . bottom of bumper is scratched up . Silver in color...
I have a 461 cubic inch SBF Yates D3 heads flowing 410+ bullet camshaft Oliver rods diamond pistons ford racing k351 aluminum block 5 stage dry sump modified 2868 edelbrock intake for D3 heads 15.4 compression Ron's 2100cfm terminator mechanical injection motor runs 5.40s at 124mph at 2700lbs with repeatable and safe fueling,timing, and shifting only at 7000rpm ... will run faster if it is lear...
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
AMP Research Power Steps in excellent condition. These steps were taken off of a 2015 Chevrolet 2500HD Crew Cab. They should fit several different years.
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
5.0 HO 302. Installed in 98 mustang 5 speed v-6 car. Whole car available as well. Can hear run and drive. Minor performance upgrades. Std bore, micropolished crank, Kings bearings. Flipped pistons. Stock HO camshaft, cloyes timing set deletes factory emissions advance heads milled to produce true 9.1 compression. Currently setting up to run in 94-95 Mustang. Head specs shaved .010 all valves an...
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
97-02 ford alternator barely used. $75. Fits various ford lincoln mercury 4.6 5.4 v-10. 8 rib 130 . R111752A part number.
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
FOR SALEAn expertly rebuilt 402c.i, 2 bolt main CE warranty replacement L34 engine assembly-sted CE1 for 1971 calendar year engine warranty replacement. Originally in a Black Cherry 70 Chevelle SS. This engine block has casting 3969854. Expertly rebuilt by Mark Small in Westminster, MD. Dyno-tested and puts out over 400hp 5500rpm. Intake is dated 70. Heads are dated 70 casting 3964290 are close...
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
6040 blue bench seat out of early 90s chevy truck ext cab. No head rest holes never had head rests. They need shood and installed. $250 cash or they stay here. Located 5 miles N of Riverton Ks417 439 fi ve ni ne 5 Oh
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
Front 23 of frame off 1975 K20. Straight. Great piece to pull measurments and then pull brackets to do a 24wd swap.Located 5 miles N of Riverton Ks$245 cash Have equipment to load on your trailer. 417 439 fi ve ni ne fi ve oh
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
NV4500 - 2wdBought a group of NV4500s from tranny shop.This has early GM bellhousing pattern. Missing ext housing rear yoke. Looks like new inside. Selling as is. $375 cashLocated 5 miles N or Riverton Ks417 439 fi ve ni ne fiv e oh
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
Complete dana 44 HD fnt axle flat top knuckles slicer lock outs w sway bar - 8 lug off of a 1975 K20 cer special. Ill cut U bolts and knock off pitman arm.$675Have tractor to load out.Located 5 miles N of Riverton Ks
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
Tach dash w capacitor for tach , mech oil pressure gauge , plug for dash , plug for tach , plug for fuse panel. Never tested or used. One mount tab on outer housing is broke - have the tab. Came out of a 1975 K20 cer special I parted. $175 cashLocated 5 miles N of Riverton Ks.
8-Jan-2019Joplin, MO+15 milesAuto Parts for Sale
Dash cut out of a 66 GMC 12 ton. I cut it behind the pinch weld. Nice piece to do repair on a cut up dash. Located 5 miles N Riverton Ks$145 cash